Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
2006 Tiare Sovran 3600 how do I remove the steering wheel?
#1
Somehow I think I bent (warped) the steeling wheel, and I would like to have it straightened.  I got the cap off, and then there is a nut, I got the nut off, but nothing.  I cant tell if there is a retaining ring, or snap clip or not that needs removed.  Someone suggested beating on the nut and it should pop lose.  So Before I try that, I thought I would ask, and see if there is something simpler.  TIA

(it is one of those pretty big (2'?) in diameter wheels with wood on the outside)
Reply
#2
(01-23-2017, 02:18 PM)sluggo Wrote: Somehow I think I bent (warped) the steeling wheel, and I would like to have it straightened.  I got the cap off, and then there is a nut, I got the nut off, but nothing.  I cant tell if there is a retaining ring, or snap clip or not that needs removed.  Someone suggested beating on the nut and it should pop lose.  So Before I try that, I thought I would ask, and see if there is something simpler.  TIA

(it is one of those pretty big (2'?) in diameter wheels with wood on the outside)

I've removed mine, after removing the center bolt, you need a puller, I got one at a local autozone. Mine was the
kind with 3 adjustable grabbers and a center bolt, you adjust it and turn the bolt
on the center, it came off easily.

Mine was similar to this one:
http://www.autozone.com/test-scan-and-sp...ckfit=true

You put the center bolt (with the point) in the center of the bolt (that you removed the nut from), then adjust the grabbers around the stainless ring, then using a wrench turn the center bolt.

Basically like this:

http://continuouswave.com/whaler/referen...00x450.jpg
Reply
#3
(01-23-2017, 02:40 PM)efontana Wrote:
(01-23-2017, 02:18 PM)sluggo Wrote: Somehow I think I bent (warped) the steeling wheel, and I would like to have it straightened.  I got the cap off, and then there is a nut, I got the nut off, but nothing.  I cant tell if there is a retaining ring, or snap clip or not that needs removed.  Someone suggested beating on the nut and it should pop lose.  So Before I try that, I thought I would ask, and see if there is something simpler.  TIA

(it is one of those pretty big (2'?) in diameter wheels with wood on the outside)

I've removed mine, after removing the center bolt, you need a puller, I got one at a local autozone. Mine was the
kind with 3 adjustable grabbers and a center bolt, you adjust it and turn the bolt
on the center, it came off easily.

Mine was similar to this one:
http://www.autozone.com/test-scan-and-sp...ckfit=true

You put the center bolt (with the point) in the center of the bolt (that you removed the nut from), then adjust the grabbers around the stainless ring, then using a wrench turn the center bolt.

Basically like this:

http://continuouswave.com/whaler/referen...00x450.jpg
Thanks!  so to be clear you have the same boat??  TIA
Reply
#4
(01-23-2017, 02:45 PM)sluggo Wrote:
(01-23-2017, 02:40 PM)efontana Wrote:
(01-23-2017, 02:18 PM)sluggo Wrote: Somehow I think I bent (warped) the steeling wheel, and I would like to have it straightened.  I got the cap off, and then there is a nut, I got the nut off, but nothing.  I cant tell if there is a retaining ring, or snap clip or not that needs removed.  Someone suggested beating on the nut and it should pop lose.  So Before I try that, I thought I would ask, and see if there is something simpler.  TIA

(it is one of those pretty big (2'?) in diameter wheels with wood on the outside)

I've removed mine, after removing the center bolt, you need a puller, I got one at a local autozone. Mine was the
kind with 3 adjustable grabbers and a center bolt, you adjust it and turn the bolt
on the center, it came off easily.

Mine was similar to this one:
http://www.autozone.com/test-scan-and-sp...ckfit=true

You put the center bolt (with the point) in the center of the bolt (that you removed the nut from), then adjust the grabbers around the stainless ring, then using a wrench turn the center bolt.

Basically like this:

http://continuouswave.com/whaler/referen...00x450.jpg
Thanks!  so to be clear you have the same boat??  TIA

Yep!
Reply
#5
(01-23-2017, 02:49 PM)efontana Wrote:
(01-23-2017, 02:45 PM)sluggo Wrote:
(01-23-2017, 02:40 PM)efontana Wrote:
(01-23-2017, 02:18 PM)sluggo Wrote: Somehow I think I bent (warped) the steeling wheel, and I would like to have it straightened.  I got the cap off, and then there is a nut, I got the nut off, but nothing.  I cant tell if there is a retaining ring, or snap clip or not that needs removed.  Someone suggested beating on the nut and it should pop lose.  So Before I try that, I thought I would ask, and see if there is something simpler.  TIA

(it is one of those pretty big (2'?) in diameter wheels with wood on the outside)

I've removed mine, after removing the center bolt, you need a puller, I got one at a local autozone. Mine was the
kind with 3 adjustable grabbers and a center bolt, you adjust it and turn the bolt
on the center, it came off easily.

Mine was similar to this one:
http://www.autozone.com/test-scan-and-sp...ckfit=true

You put the center bolt (with the point) in the center of the bolt (that you removed the nut from), then adjust the grabbers around the stainless ring, then using a wrench turn the center bolt.

Basically like this:

http://continuouswave.com/whaler/referen...00x450.jpg
Thanks!  so to be clear you have the same boat??  TIA

Yep!
Thanks again!  I'll stick it on there and try and not worry about the little thing I think is some sort of keyway.
Reply
#6
(01-23-2017, 02:52 PM)sluggo Wrote:
(01-23-2017, 02:49 PM)efontana Wrote:
(01-23-2017, 02:45 PM)sluggo Wrote:
(01-23-2017, 02:40 PM)efontana Wrote:
(01-23-2017, 02:18 PM)sluggo Wrote: Somehow I think I bent (warped) the steeling wheel, and I would like to have it straightened.  I got the cap off, and then there is a nut, I got the nut off, but nothing.  I cant tell if there is a retaining ring, or snap clip or not that needs removed.  Someone suggested beating on the nut and it should pop lose.  So Before I try that, I thought I would ask, and see if there is something simpler.  TIA

(it is one of those pretty big (2'?) in diameter wheels with wood on the outside)

I've removed mine, after removing the center bolt, you need a puller, I got one at a local autozone. Mine was the
kind with 3 adjustable grabbers and a center bolt, you adjust it and turn the bolt
on the center, it came off easily.

Mine was similar to this one:
http://www.autozone.com/test-scan-and-sp...ckfit=true

You put the center bolt (with the point) in the center of the bolt (that you removed the nut from), then adjust the grabbers around the stainless ring, then using a wrench turn the center bolt.

Basically like this:

http://continuouswave.com/whaler/referen...00x450.jpg
Thanks!  so to be clear you have the same boat??  TIA

Yep!
Thanks again!  I'll stick it on there and try and not worry about the little thing I think is some sort of keyway.

The piece of metal, "the key" stays in the square groove in the shaft and wheel hub. I replaced my wheel with a new one, and the new wheel came with a new key. Make sure you don't drop and/or lose the key. It will come right out no problem with the puller.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  3500 Sovran trimtabs drprunner 0 58 11-14-2026, 03:44 PM
Last Post: drprunner
  [Tiara Sovran] Wiper Blades 3900 Sovran Euphoria38 1 544 08-31-2026, 10:34 AM
Last Post: Herrema4
  Tiara 52 Sovran Salon Keel Question Knot On Call 2 706 08-17-2026, 05:31 PM
Last Post: Bford100
Exclamation [Tiara Sovran] Sunroof motor location on ‘13 sovran 45? Tiara45 0 494 07-28-2026, 06:28 AM
Last Post: Tiara45
  [Tiara Open] 2005 3600 Open / Bait well water deflectors KRB 3 2,870 02-23-2026, 11:01 AM
Last Post: hiccup



Users browsing this thread: 1 Guest(s)
Advertisements

Latest Threads
3500 Open deck lift piston
Last Post: hiccup
Today 08:10 AM
» Replies: 4
» Views: 1101
Oil Filter ?
Last Post: ReelMagic
Yesterday 04:23 PM
» Replies: 7
» Views: 1619
Unknown noise from Tiara 3800 Open engi...
Last Post: liambrown
Yesterday 01:54 PM
» Replies: 4
» Views: 537
Tiara 40 Express 2003 - Removal of Cleat
Last Post: saywhen
11-14-2026 05:25 PM
» Replies: 2
» Views: 380
3500 Sovran trimtabs
Last Post: drprunner
11-14-2026 03:44 PM
» Replies: 0
» Views: 58